En-Masse Conveyors
GSI En-Masse Conveyors are designed for strength and superior performance to maximize operation run time and minimize the length of delivery time. For larger grain capacity requirements, GSI offers a 26" and 32" En-masse Conveyor. These conveyors feature an extra heavy-duty construction, easy access to all vital hardware and a powder paint coated finish for lasting durability.

Trough Sections Feature...

• Dust and weather tight, heavy gauge, peaked covers on the head, tail and trough.

• Bolted removable bottom construction.

• Standard 10 gauge trough sides.

• Trough sections are fixture assembled for accurate alignment and ease of installation.

• Rail returns are standard on 20" x 20", 26" x 20", 32" x 20" conveyors. Rails are lined with 1/4" abasion resistant steel and tapered end to end to minimize flight wear and maximize cleaning. Rails overlap at flange connections for smooth operation.

• Trough sections are flanged with structural angle to provide rigidity and accurate alignment.

• Standard roller chain engineered for each specific conveyor to maximize working load and expected life.

• UHMW flights prevent steel to steel contact.

• UHMW return rollers with shafts bolted to the trough for easy maintenance and replacement.

En-Masse Conveyor Specifications
--------------------
Bucket Elevators
--------------------
En-Masse Conveyors
--------------------
Hi-Flight Conveyors
--------------------
Roller Belt Conveyors
--------------------
Accessory Equipment

En-Masse Conveyor standard features and options include...

• Abrasion resistant steel wear liners with recessed fasteners for removal or replacement (see below)

• Slack chain switch

• Hinged head relief door with limit switch standard

• Bypass inlet hopper

• Manual or electric head and intermediate discharge gates

• Head and tail housing split for shaft and sprocket removal

• Standard split sprockets

• Conveyor support legs

• Chain options available

• Chain rail returns available on 20" (508 mm) tall conveyors (14" (355.6 mm) and 16" (406.4 mm) wide.

Accessory Equipment
Valves, elbow, connectors, adapters, dead-stops and more...

Liner Packages

Liner Package #1
3/16" medium hard abrasion resistant bottoms

Liner Package #2
10 gauge bolted medium hard abrasion resistant side liners and 3/16" medium hard abrasion resistant bottoms.

Liner Package #3
3/16" bolted medium hard abrasion resistant side liners and 1/4" medium hard abrasion resistant bottoms.

Conveyor Head Section

• Extended mount flange bearings on 12" (304.8 mm) and 14" (355.6 mm) tall conveyors. External mount pillow block bearings on 20" (508 mm) tall conveyors.

• Machined 1/4" (6.35 mm) thick UHMW shaft seals.

• Flame cut hardened steel sprockets.

• Maintenance friendly, bolted access to allow removal of the shaft, sprocket, and bearings as an assembly.

• 10 gauge housing on 12" and 14" conveyors, 7 gauge on 20" conveyors.

• Head shafts are turned ground and polished.

Conveyor Tail Section

• Extended mount flange bearings on 12" (304.8) and 14" (355.6 mm) tall conveyors. External mount pillow block bearings on 20" (508 mm) tall conveyors.

• Heavy duty chain tension take-up system utilizing corrosion resistant acme threaded screws.

• Flame cut hardened steel sprockets.

• Maintenance friendly, bolted access to allow removal of the shaft, sprocket, and bearings as an assembly.

• 10 gauge housing on 12" and 14" conveyors, 7 gauge on 20" conveyors.

Intermediate Trough Sections

• Conveyors are highly corrosion resistant and come standard with a powder coat finish for lasting durability and superior appearance. (Also available in galvanized construction)